2016 Peterbilt 567
Cummins ISX 15
CUSCO DOT TURBOVAC 3627 WITH BOOM, EQ# 10312
3600 USG + 3% Outage
Design shall withstand 25-PSI internal pressure and 15 PSIG external pressure (full vacuum) and shall meet all the requirements of Section VIII Division 1 of the A.S.M.E. Boiler and Pressure Vessel Code. National Board Registered.
-20 to 200 degrees F
HYDROSTATIC TEST PRESSURE:
Withstand 25 PSI
Withstand 15 PSIG
4" SS Girard pressure vent, 25 PSIG setting mounted top of tank.
8” internal shut-off with 12" stainless steel float ball/cage assembly and 8" rubber seat.
One anti surge mounted on reinforcing pad.
Circumferential reinforcement rings with tank support feet.
Front, center, and rear 4" pipe construction overturns with reinforcement pads and gussets.
20" diameter located top of tank.
LIQUID LEVEL INDICATOR:
Stainless Steel construction rotary float gauge with 6” float ball assembly located on rear head.
Hydraulic full opening rear door assembly with 6 heavy duty wing clamps, neoprene rubber rear door gasket, double acting hydraulic cylinder and safety brace.
6" ANSI Betts air open/spring close valve and Betts actuator, 6" sand pipe / deflector plate assembly, aluminum Kamlok fittings mounted on rear head at 4 o’clock position.
6" ANSI Betts air open/spring close valve and Betts actuator with aluminum Kamlok fittings mounted on bottom center of rear door.
8” air operated butterfly valve between primary and cyclone with manual air switch control.
Dual 20" diameter cyclones mounted on 20" diameter drop box with side swing clean out, 3" brass drain valve and aluminum Kamlok fittings, Cusco 30" diameter final filter assembly installed for protection of blower with 20” diameter stainless steel 100 micron filter.
12" intake and exhaust silencers.
Roots DVJ 721 Blower 3658 CFM free air rating, 2850CFM @ 18"Hg, 27"Hg maximum vacuum
Single 8" diameter with 8" quick disconnect rubber boot assembly
6" manual butterfly vacuum relief valve and 10" inline check valve assembly
Driven from air shift transfer case.
PRESSURE UNLOADING SYSTEM:
Moro PM80 air cooled vacuum/pressure pump (350 CFM free air 28" Hg) hydraulically driven with 3" air operated isolation butterfly valve, 3" diameter no disconnect piping, 3" secondary moisture trap filter and muffler/oil trap assembly.
Mounted on hydraulic dump sub-frame with suction strainer, diffuser, fill cap, hydraulic oil filters and sight glass.
HYDRAULIC DUMP SYSTEM:
Full length hydraulic dump sub-frame with 20 ton, 3 stage single acting dump cylinder, rear dump pivot assembly and safety brace.
Hydraulic vibrator assembly mounted bottom of tank with reinforcing pad, heavy duty mounting channel and pressure relief valve.
3-spool valve body for control of pressure unloading system/vibrator, rear door and hydraulic dump complete with hydraulic pressure gauge. Controls to be located on the driver side of unit near control panel.
Turbovac gauge panel assembly with tank vacuum/pressure gauge, filter element vacuum gauges, tachometer, throttle control and 3” isolation valve control. Panel to be lighted for night operation. Panel to be located on the driver side of unit near hydraulic controls.
Full-length side boxes for hose storage / fender assembly with anti-sail mud-flaps and rear tire skirt.
Ladder assembly, four numbered placards, 50' static line, and steel toolbox assembly 36” wide x 18” deep x 18” high.
DOT lighting with three lamp rear module assembly, clearance lamps, reflectors, three in a row clearance markers, two rear halogen flood lights and one at control, and one rear amber strobe beacon.
DOT rear bumper for protection of external valves with platform/step assembly and rear dirt shield.
ADDITIONAL ITEMS INCLUDED:
- Dual rear mounted hose hooks located as low as possible on rear head.
- Water jackets installed on rear valves for future installation of heated valve option.
Complete system installed on a 2015 Peterbuilt 567, Cummins ISX15, 450HP, Eaton FRO-16210C
Give Us A Call For More Sales & Rental Information