Available Inventory

2015 Cusco Turbovac

Click Image to Enlarge

General Details:

EQ #:8774
VIN #:1NKDX4EX2FJ444637
Chassis:
2015 Kenworth T800
Engine:
Cummins ISX 15
Vacuum System:
Roots DVJ 721
GAWR:
78,350 lbs

Specifications:

CUSCO TURBOVAC HI LOADER, EQ# 8774

TANK CAPACITY:
3200 USG + 3% Outage

HEAD MATERIAL:
0.3125 SA516-70

SHELL MATERIAL:
0.3125 SA516-70

TANK DIAMETER:
78" OD Front, 42” OD Rear Eccentric

OPERATING TEMPERATURE:
-20 to 200 degrees F

HYDROSTATIC TEST PRESSURE:
40.0 PSIG

PRESSURE RELIEF:   
4" SS Girard pressure vent, 25 PSIG setting mounted top of tank.
   
PRIMARY SHUT-OFF:
8” internal shut-off with 12” stainless steel float ball/cage assembly and 8” rubber seat.

BAFFLE:
One anti surge mounted on reinforcing pad.

RINGS:
Circumferential reinforcement rings with tank support feet.

OVERTURN PROTECTION:
Front, center, and rear 4" pipe construction overturns with reinforcement pads and gussets

MANWAY:   
20" diameter located top of tank.

LIQUID LEVEL INDICATOR:
Stainless Steel construction rotary float gauge with 6” float ball assembly located on driver’s side front of tank shell.
   
REAR DOOR:
Hydraulic full opening rear door assembly with 4 heavy duty wing clamps, neoprene rubber rear door gasket, double acting hydraulic cylinder.

SUCTION VALVE:
6” Betts air operated valve with 6” sand pipe/deflector plate assembly, aluminum Kamlok fittings mounted on transition.

DISCHARGE VALVE:   
6” Betts air operated valve with 6” annual ball valve in series and aluminum Kamlok fittings with 1” drain valve in cap, mounted on bottom transition.

ISOLATION VALVE:
8” air operated butterfly valve between primary and cyclone with PTO interconnect.

FILTRATION SYSTEM:
6” cyclone mounted on 20” diameter drop box with side swing clean out, 4” brass drain valve and aluminum kamlok fittings 20” diameter washable inline SS/fiber filter element, 100 micron for protection of blower.

SILENCERS:   
12" intake and exhaust silencers.

BLOWER PIPING:
Single 8" diameter with 8” quick disconnect rubber boot assembly.

BLOWER VALVING:
4" brass manual vacuum relief valve and 10" inline check valve assembly

DRIVE:
Direct drive from air shift transfer case.

PRESSURE UNLOADING SYSTEM:
Moro PM80 air cooled vacuum/pressure pump (350CFM free air 28” Hg) hydraulically driven from 6 bolt air shift PTO with 3” air operated isolation butterfly valve, 3” diameter no disconnect piping, 4” secondary moisture trap filter and muffler/oil trap assembly.

HYDRAULIC RESERVOIR:
Mounted on hydraulic dump sub-frame with suction strainer, diffuser, fill cap, hydraulic oil filters and sight glass.

HYDRAULIC DUMP SYSTEM:
Full length hydraulic dump sub-frame with 20 ton, single acting dump cylinder, rear dump pivot assembly and safety brace.

VIBRATOR:
Hydraulic vibrator assembly mounted bottom of tank with reinforcing pad, heavy duty mounting channel, pressure relief valve and variable speed control.

HYDRAULIC CONTROLS:
3-spool valve body for control of hydraulic dump, rear door, vibrator, and pressure unloading system/vibrator, rear door and hydraulic dump complete with Hydraulic pressure gauge.  Controls to be located on the driver side of the unit near control panel.
 
GAUGES:
Turbovac gauge panel assembly with tank vacuum/pressure gauge, hydraulic pressure gauge and filter element vacuum gauges, tachometer, throttle control and 3” isolation valve control.  Panel to be lighted for night operation.  Panel to be located on the driver side of unit near hydraulic controls.

SIDE TRAYS:
Full-length side boxes for hose storage / fender assembly with anti-sail mud-flaps and rear tire skirt.

TRIM:
Ladder assembly, four numbered placards, 50' static line and steel toolbox assembly 36” wide x 18” deep x 18” high.

LIGHTING:
DOT lighting with three lamp rear module assembly, clearance lamps, reflectors, three in a row clearance markers, two rear spotlights, one spot light at operator controls, and one rear amber rotating beacon.

BUMPER:
DOT rear bumper for protection of external valves with platform/step assembly and rear dirt shield. Bumper drip tray with 2” manual drain valve.  2 additional steps on top of rear bumper for easy access to rear door wing nuts.

WATER JACKETS:
Installed on rear valves for future installation of heated valve option.

PAINTING:
The entire tank and body of the vacuum system shall be sandblasted and primed with two (2) coats of primer and painted with two (2) coats of single stage Sherwin Williams paint. Please note there may be an additional cost for base coat clear coat cab matches in the event that your proposed paint color cannot be matched to a Sherwin Williams single stage paint code.

BOOM:
6” Moro hydraulic boom assembly with 320 degree hydraulic rotation, 4 ft. hydraulic extension, plunger valve and remote pendent control, both wired and wireless.

INSTALLATION:
Complete system installed on 2015 Kenworth T800

    888-936-4369
    Give Us A Call For More Sales & Rental Information

    All advertised prices exclude government fees and taxes, any finance charges, any dealer document preparation charge, and any emission testing charge. Vehicles are subject to prior sale. All advertised to be true but not guaranteed.