CUSCO DOT DURAVAC 820 VACUUM COMBO UNIT, EQ# 8768
3200 USG + 3% Outage (approx 12 cubes)
Design shall withstand 25-PSI internal pressure and 15 PSIG external pressure (full vacuum) and shall meet all the requirements of Section VIII Division 1 of the A.S.M.E. Boiler and Pressure Vessel Code. National Board Registered. Tank to be designed and constructed in full compliance with Transport Canada TC 407 / 412
-20 to 200 degrees F
HYDROSTATIC TEST PRESSURE:
4" SS Girard pressure vent, 25 PSIG setting mounted top of tank.
6" internal shut-off with 12" SS float ball and cage assembly with neoprene rubber seat top front of tank.
One bolt on anti surge mounted on reinforcing pad.
Circumferential reinforcement rings with tank support feet.
Front, dual center, and rear 4" pipe construction overturns with reinforcement pads and gussets
LIQUID LEVEL INDICATOR:
Stainless Steel construction rotary float gauge with 6” float ball assembly located on front driver side with grab handle and up position tie back.
Hydraulic full opening rear door assembly with 6 heavy duty wing clamps, neoprene rubber rear door gasket, double acting hydraulic cylinders and safety brace.
One 6” ANSI flange Betts air operated valve and Betts actuator with 6” sand pipe / deflector plate assembly, aluminum Kamlok fittings and one 4” ANSI flange Betts air operated valve and Betts actuator with aluminum Kamlok fittings mounted on rear head at 8:00 o’clock. Note the 8:00 position is not to include a sand pipe assembly.
6" ANSI flange Betts air operated valve and Betts actuator with aluminum Kamlok fittings mounted on rear head.
6” air operated butterfly valve between primary and secondary shut-off controlled by manual air switch.
Cusco all stainless steel 30” diameter final filter assembly installed for protection of blower with 20” diameter 100 micron filter and drain valve.
High capacity cyclone assembly with 12” diameter drop box with bottom mounted clean out door, and 2” brass gate valve, Kamlok and cap. Cyclone installed on front of head of tank curbside.
6" intake and exhaust silencer with exhaust line to curbside and driver side of truck.
Single 6" diameter no disconnect piping to allow tank to dump with composite hose and Victaulic fittings, vacuum system connected with vacuum pump flush port, air operated butterfly valve assemblies for pressure unloading and dual 6" inline check valve assemblies.
Hibon VTB-820, 1400 CFM free air rating, 1100 CFM @ 18"Hg, 27"Hg maximum vacuum.
Hydraulically driven from air shift PTO mounted on transmission with remote mount hydraulic pump, motor and oil cooler.
BLOWER FLUSH SYSTEM:
Diesel fuel supply line with valve from separate diesel fuel tank.
Mounted on hydraulic dump sub-frame with suction strainer, diffuser, fill cap, hydraulic oil filters and sight glass.
HYDRAULIC DUMP SYSTEM:
Full length hydraulic dump sub-frame with 20 ton Mailhot single acting dump cylinder, rear dump pivot assembly and safety brace.
3-spool valve body for control of hydraulic dump, rear door ,vibrator. Single spool valve body for wash pump.
Glycerin filled vacuum/pressure gauge and hydraulic pressure gauge.
Western style full length side boxes for hose storage / fender assembly with heavy duty out riggers, anti-sail mud flaps and rear 45 degree full coverage tire skirt.
Ladder assembly on water tank portion with 6-point attachment for access to water tank manway, four numbered placards and 50' static line, DOT LED moisture proof lighting, three (3) lower lamp assembly, dual upper turn and brake lamp assembly, five (5) side marker lights on side tray, three (3) in a row clearance markers.
DOT LED moisture proof lighting with rectangular three lower lamp assembly, dual upper turn and brake lamp assembly, 5 side marker lights on side tray, clearance lamps, reflectors, three in a row clearance markers, upper license plate mount and light assembly. Four rear facing rectangular halogen flood lights, and one located at blower area. One rear amber strobe light.
DOT rear bumper for protection of external valves with grated platform/step assembly and rear dirt shield. Rear bumper will have removable insert.
The entire tank and body of the vacuum system shall be sandblasted and primed with two (2) coats of primer and painted with two (2) coats of single stage Sherwin Williams paint. Please note there may be an additional cost for base coat clear coat cab matches in the event that your proposed paint color cannot be matched to a Sherwin Williams single stage paint code."
ADDITIONAL ITEMS INCLUDED:
1000 USG (approx 4 cube) steel water compartment front of waste tank, sandblasted and coated on interior with heavy duty POR15 sealant, with 20” manway, 3” air operated BF drain valve, heated supply line with valve and quick disconnect, strainer, stainless steel construction rotary float gauge with 6” float ball assembly located on front passenger side with grab handle and 3” brass fill port on curb side with line to top of compartment with kamlok and cap connection. Fill port valve and drain valve to be heated. Water tank re-circulating system with burner operational.
HIGH PRESSURE WASH SYSTEM:
CAT 3560 water pump with suction strainer, pressure relief valve, Two (2) steam rated Hannay hydraulic rewind hose reels c/w 75’ 3/8” high pressure hose. Complete wash pump and reel mounted on passenger side, in a painted steel insulated cross box with 2 high capacity bus heaters and polished SS doors installed behind truck cab with light and small hose access doors for hose reels. Includes handgun and steam wand.
WATER PUMP DRIVE:
Water pump to be driven via load sensing hydraulic system with adjustable pressure and speed controls.
WASH SYSTEM OPERATION:
Wash system has dedicated steam hose reel and hot water hose reel. Wash to be set-up to run one or both hose reels at the same time for hot water only not steam. Water system to be set to maximum 3000psi and 20GPM. Note: water pump to operate at same time as blower.
HOT WATER SYSTEM:
980,000 BTU/hr with steam kit and 3000 Watt 110 volt inverter with additional outlet in burner cabinet. Diesel fuel filter system with water separator. Water supplied from wash system. Burner mounted in the center of heated and insulted cross box, exhaust stack for burner. Glycol flush tank included for winterizing system c/w air purge.
HEATED JACKETED VALVE:
Assembly for 4” or 6” rear valves, isolation valve, water tank drain, fill valve and cyclone drain valve.
One (1) 72” toolbox mounted on driver’s side side tray, spaced up 1” from checker plate for cleaning. Note: Side swing doors.
Two (2) Solid mount chain hangers, one mounted each side complete with locking bar
All doors to be polished SS
30lb ABC fire extinguisher mounted on driver’s side
Complete system installed on a 2015 Western Star 4900 SB chassis, Cummins ISX-15, 500HP, Eaton Fuller RTLO-16919B